2 in 1: Pole Saw / Chain Saw ENScie sur manche et tronçonneuse 2 en 1 F 2 en 1: sierra de pértiga/sierra de cadena ESP07P24P43WG
2 in 1: Pole Saw / Chain Saw EN10protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure
2 in 1: Pole Saw / Chain Saw EN11injury and should never be done.3. Hold the power tool by insulated gripping surfaces only, because the saw chain ma
2 in 1: Pole Saw / Chain Saw EN12SAFETY RULES FOR EXTENSION CORDMake sure your extension cord is in good condition. When using an extension cord, be
2 in 1: Pole Saw / Chain Saw EN13SJOW-A, SJTW-A. or SJTOW-A.9) Avoid Unintentional Starting - Don’t carry plugged-in appliance with finger on switch.
2 in 1: Pole Saw / Chain Saw EN14damage. If the tree does make contact with any utility line, the company should be notified immediately.The chain sa
2 in 1: Pole Saw / Chain Saw EN15When the log is supported on one end, as illustrated in Figure IV, cut 1/3 the diameter from the underside (underbuc
2 in 1: Pole Saw / Chain Saw EN16SYMBOLTo reduce the risk of injury, user must read instruction manual Wear ear protection
2 in 1: Pole Saw / Chain Saw EN17ASSEMBLYWARNING! Do not connect the chain saw to the power supply before it is completely assembled.Always use glove
2 in 1: Pole Saw / Chain Saw EN18at end of inner pole.(See Fig. G2) WARNING!• Before attaching the power cord of the machine to the power cord of
2 in 1: Pole Saw / Chain Saw EN19For switching off, release the On/Off Switch.2. CUTTINGIMPORTANT: Is the oil reservoir filled? Check the Oil Level Wi
2 in 1: Pole Saw / Chain Saw EN205. Use the Bumper Spikes as a leverage point (a) while cutting. (See Fig. K2)6. Do not operate the chain saw with
2 in 1: Pole Saw / Chain Saw EN213. Make third cut as close to tree trunk as possible on underside of limb stub. Use top of guide bar to make this c
2 in 1: Pole Saw / Chain Saw EN22File Rail Edges and SidesSquareWorn Groove Correct GrooveReplace the guide bar when the groove is worn, the guide b
2 in 1: Pole Saw / Chain Saw EN23TROUBLESHOOTING TABLEThe following table gives checks and actions that you can perform if your machine does not oper
1101214341520171819212131186 79523 24292725 26 2816
EN: Injecting grease to lubricateES: Inyectando grasa para lubricarF: Injectez la graisse pour lubrifieraF2 G1 G2HM1 M2 M3M5M4 M61090.12-0.24”(3-6mm)E
EN: Injecting grease to lubricateES: Inyectando grasa para lubricarF: Injectez la graisse pour lubrifieraF2 G1 G2HM1 M2 M3M5M4 M61090.12-0.24”(3-6mm)E
EN: Injecting grease to lubricateES: Inyectando grasa para lubricarF: Injectez la graisse pour lubrifieraF2 G1 G2HM1 M2 M3M5M4 M61090.12-0.24”(3-6mm)E
2 in 1: Pole Saw / Chain Saw EN71. REAR HANDLE2. ON/OFF SWITCH3. LOCK-OFF BUTTON4. OIL LEVEL WINDOW5. OIL FILLER CAP6. FRONT HANDLE7. HAND GUA
2 in 1: Pole Saw / Chain Saw EN8TECHNICAL DATAWG309 WG310Voltage 120V~60HzAmps 8AmpBar length 10“ 8”Chain speed 28ft/s Oil tank capacity 4.06ounce
2 in 1: Pole Saw / Chain Saw EN9WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains ch
Kommentare zu diesen Handbüchern